← All blogs

Cedar Park TX Whole-Home Rewiring Costs — Electrical Guide

Still living with knob and tube wiring? This guide explains knob and tube wiring replacement cost in plain English, so you can plan with confidence. We cover price ranges, what drives costs, permits, timelines, and smart upgrades to bundle now. If you are in Austin or nearby, we can provide a free in‑home inspection and an upfront estimate before any work begins.

What is knob and tube, and why replace it

Knob and tube, common from the 1880s to the 1940s, uses ceramic knobs and tubes to route single insulated conductors. It typically lacks an equipment grounding conductor, which limits modern safety and device protection. Splices may be hidden behind walls. Insulation over old K&T can also create heat buildup.

Two hard facts matter for Texas homeowners:

  1. Texas adopted the 2023 National Electrical Code on September 1, 2023 through TDLR. New work must meet current NEC requirements.
  2. Modern protection like GFCI and AFCI is required in many locations. Kitchens, bathrooms, laundry areas, outdoors, and garages need GFCI. Most living areas need AFCI. These protections are not native to old K&T.

Home insurers often restrict or surcharge policies for active K&T. Replacement increases safety, reduces nuisance trips and voltage drop, and supports EV charging, heat pumps, smart panels, and surge protection.

Average cost ranges in the Austin area

Every home is different, but these ballpark ranges help you budget. Final pricing follows an on‑site inspection and a written, upfront estimate.

  1. Small homes or condos up to 1,000 sq ft: 7,500 to 15,000
  2. Mid‑size homes 1,200 to 2,000 sq ft: 12,000 to 25,000
  3. Larger homes 2,200 to 3,000 sq ft: 20,000 to 40,000+

What changes the number:

  • Access. Plaster, lathe, tight crawlspaces, and limited attic access increase labor.
  • Wall and ceiling restoration. Electrical cost excludes drywall and paint unless bundled.
  • Panel capacity. Many K&T homes need a panel upgrade or fuse to breaker conversion.
  • Circuit count. Dedicated circuits for appliances and tech add materials and labor.
  • Permits, inspections, and engineering. Required for code compliance.
  • Live‑in phasing. Working around occupancy adds setup and cleanup time.

Local note. In Austin’s older central neighborhoods like Hyde Park or Travis Heights, plaster walls and limited chases often add time compared to newer builds in Round Rock or Leander.

What is included in a professional K&T replacement

A full rewire should be scoped clearly so you know exactly what you are buying. Our typical scope includes:

  • Running new grounded circuits throughout the home
  • Installing GFCI and AFCI protection in required areas
  • Upgrading the main electrical panel when needed
  • Adding or relocating outlets to match modern layouts and code spacing
  • Whole‑home surge protection to safeguard electronics
  • Dedicated circuits for high‑demand appliances and HVAC
  • Final testing, labeling, and documentation for insurance and resale

For many older homes we recommend a phased plan. Work can align with remodels or room additions to minimize disruption and spread cost over time.

Line‑item cost drivers you can control

You have options that move the budget up or down while staying safe and compliant.

  1. Panel upgrade choices
    • Standard 200A panel vs. smart panel like SPAN.
    • Fuse to breaker conversion when legacy equipment remains.
  2. Circuit strategy
    • Baseline code minimum vs. comfort upgrades like extra kitchen small‑appliance circuits or workshop circuits.
  3. Device and trim level
    • Standard receptacles and switches vs. tamper‑resistant, USB, or smart controls.
  4. Access planning
    • Coordinated drywall cuts with a remodeler can lower patch costs.
  5. Scheduling
    • Vacant home or short‑term move out speeds production and reduces setup time.

We always provide a free in‑home inspection for rewiring projects and a written, upfront estimate so you can see how each decision affects price.

Permits, inspections, and code compliance in Texas

Electrical rewires require permits and inspections by the local authority having jurisdiction. Your electrician pulls the permit, coordinates inspections, and closes them out. Since Texas adopted the 2023 NEC, expect the following on a K&T replacement:

  • GFCI protection in kitchens, bathrooms, laundry areas, garages, and outdoors
  • AFCI protection in most habitable rooms
  • Tamper‑resistant receptacles in areas accessible to children
  • Proper box fill, grounding, bonding, and labeling
  • Smoke and carbon monoxide alarms per current rules when triggers apply

A compliant rewire protects your family and eases insurance and appraisal questions at sale time.

Timeline and what to expect during the project

Typical timelines in the Austin area:

  • Walkthrough and estimate: 1 to 2 visits
  • Permit approval: 3 to 10 business days depending on workload
  • Active rewiring: 5 to 15 working days for an occupied 1,500 to 2,000 sq ft home
  • Inspections: rough‑in plus final, scheduled during the job
  • Wall and paint restoration: same week if bundled, or by your chosen contractor

How we minimize disruption:

  • Phased room‑by‑room planning so parts of the home stay usable
  • Daily cleanup and clear labeling of temporary circuits
  • Optional temporary power solutions for critical appliances

Expect short power‑off windows during panel work and circuit changeovers. We coordinate these around your schedule.

Smart upgrades to bundle during a rewire

Since walls are open and circuits are being built new, it is the perfect time to add value.

  • EV charging. Run a dedicated 240V circuit to the garage or driveway.
  • Surge protection. Whole‑home devices protect HVAC, appliances, and electronics.
  • Data and Wi‑Fi backbone. Pull CAT6 to offices and media spaces.
  • Lighting plan. Add recessed LED, under‑cabinet, and exterior security lighting.
  • Smart panel or energy management. SPAN panels provide circuit‑level control and backup readiness.
  • Generator readiness. Transfer switch or interlock now saves labor later if you add a standby generator.

Bundling reduces labor duplication and sets your home up for future tech without repeated wall cuts.

How Austin homes with plaster and lathe affect pricing

Classic bungalows and four‑squares often include thick plaster and limited wire chases. Opening and fishing these walls is slower than drywall. Expect more time for protection, careful drilling, and patching. When ceilings are shiplap or attic space is tight, we may run new home runs from the basement or crawlspace where available.

Ways to control costs in these homes:

  • Approve a clear patch plan up front
  • Group device height changes by room
  • Combine rewire work with planned kitchen or bath remodels

Financing, scheduling, and phasing options

Big electrical projects are an investment. We offer financing through GreenSky for qualified customers. Many owners split the project into phases, starting with high‑risk areas and the main service equipment, then bedrooms and living areas, and finally accessory spaces and exterior circuits.

Typical phase order:

  1. Service and panel upgrade, grounding and bonding
  2. Kitchen, bath, and laundry circuits with GFCI
  3. Bedrooms and living areas with AFCI
  4. Exterior lighting and accessory buildings

Phasing keeps you operational while steadily removing K&T from the home.

Red flags that signal it is time to replace K&T now

Some signs mean you should get an inspection and estimate soon:

  • Warm or discolored outlets and switches
  • Two‑prong receptacles and frequent tripping
  • Visible porcelain knobs, brittle insulation, or cloth‑covered conductors
  • Undersized or obsolete fuse panels
  • Add‑on power strips and extension cords everywhere

If any of these sound familiar, schedule a licensed inspection. We will verify conditions and provide options with clear pricing.

What our whole‑home rewires include after install

Safety does not stop at the final inspection. We offer annual maintenance options for systems we install, including SPAN smart panels and standby generators, plus priority support if issues arise. For EV chargers, our maintenance plans help keep the unit in top condition with prompt support whenever you need it. We also recommend an electrical inspection every 3 to 5 years, and more often for homes older than about 40 years.

What Homeowners Are Saying

"They were hired to rewire my main house with the power pole outside and then completed the new house for the same job. It’s a success both homes have power. ... I recommend this company 5 out of 5 stars!"
–Joshua S., Electrical Rewire

"Can’t thank them enough for all the work they did replacing my main panel and running a new line to my garage. Cheers yall, I’ll be coming back to you guys every time"
–Preston F., Electrical Rewire

"... then performed whole house type inspection. Gave me an estimate, went to work. I'm so glad I called ATeam"
–Brenda F., Electrical Rewire

"He also did a free once over of my electrical system to let me know what might need updating going forwards. A great job at a great price from a great company. Couldn't be happier."
–Lyle M., Electrical Rewire

Frequently Asked Questions

How much does it cost to replace knob and tube in a 1,500 sq ft Austin home?

Most 1,500 sq ft homes land between 15,000 and 28,000 depending on access, panel upgrades, circuit count, and wall repairs. A written on‑site estimate is the final word.

Can I keep some knob and tube if it still works?

We recommend full replacement. K&T lacks grounding and does not support modern protection. Partial keep‑alive may be allowed short term only if clearly separated and documented.

Do I need to upgrade my electrical panel during a rewire?

Often yes. K&T homes frequently have fuse panels or small breaker panels. A modern 200A panel with AFCI and GFCI coverage supports today’s loads and code.

Will my walls be opened during the project?

Usually yes. We fish many runs, but plaster and lathe often require strategic openings. Agree on the patch plan and whether your electrician or a drywall pro handles repairs.

How long will my power be off?

Most of the home stays on. Expect short outages during panel swaps and circuit changeovers, scheduled to fit your routine.

In Summary

Replacing knob and tube is one of the highest‑value safety upgrades you can make. You get grounded circuits, GFCI and AFCI protection, cleaner power, and readiness for EV charging and smart panels. If you are comparing knob and tube wiring replacement cost in Austin or nearby cities like Round Rock and Georgetown, we will guide you with a clear scope, phasing options, and an upfront estimate.

Talk to an Electrician Today

Call A Team Home Services at (737) 306-0078 or visit https://callateamtoday.com/ to schedule your free in‑home inspection for rewiring. Prefer texting first? Use our site chat to share photos for a quick, no‑obligation consult. Ready when you are.

Call now: (737) 306-0078 • Online: https://callateamtoday.com/ • Serving Austin, Round Rock, Georgetown, Cedar Park, Leander, Pflugerville, Hutto, Manor, Taylor, and Elgin.

A Team Home Services is Austin’s trusted, licensed electrical contractor for whole‑home rewiring, panel upgrades, EV chargers, and SPAN smart panels. We are Google Guaranteed, BBB A+ accredited, and recipients of top industry awards. Homeowners choose us for upfront estimates, competitive pricing, and fast, responsive service. Our certified team follows the National Electrical Code and local requirements on every job. We offer phased rewires to reduce disruption, financing through GreenSky, and maintenance options for systems we install. Count on clear communication, tidy workmanship, and long‑term safety.

Sources 12

Need Help With Your Home?

Turn helpful advice into action with professional service from our experienced technicians.

Call now